Call Today: 716.741.1141 | E-mail: sales@appliedprocessor.com
PWM Solenoid
Driver/Control
Products
Model 205 Model 400 USB  *NEW* Model 400 Legacy Model 402Model 500


Signal Conditioning
Products
SGC 200SGC 400 / SGC 401 DFA 100

Motion Control Products
SACT 100 SACT 101



Electronic Engineering
Design Services


 


We Accept:

American Express MasterCard VISA

Signal Conditioning Products

Applied Processor and Measurement, Inc. has been supplying electronic signal conditioners for industrial and automotive applications and equipment integrators for nearly 25 years.

Please use the tables below to select the signal conditioner for your application.

SGC-200 Current Sense Driver

SGC-200 Current Sense Amplifier

The Model SGC-200 module provides two amplified voltage outputs proportional to current across an internal sense resistor for current measurement of PWM pulse solenoids and DC motor applications.

Model Application Input Output Features
SGC-200

SGC-200 Data Sheet
Data Sheet
(PDF - 108KB)
  • current measurement of pulsed solenoids, actiuators and DC motors
  • component test and development
  • general purpose signal condioner for data acquisition and control applications including PLC interface
  • +/- 4A
  • 16 to 1kHz
  • +/- 10V max
  • analog output, single ended, DC coupled
  • switch-selectable or fixed gain
  • DIN mountable

 

SGC-400 Isolated Low-Side Driver

SGC-400 Isolated Low-Side Driver

The Model SGC-400 module turns a low drive signal into a 50W peak low-side drive control signal for PLC and PC solenoid and actuator drive applications.

Model Application Input Output Features
SGC-400

SGC-400 Data Sheet
Data Sheet
(PDF - 115KB)
  • solenoid driver
  • solid-state switch
  • high-current driver
  • PLC, PC interface
  • 0 to 3.3V or 0 to 24V
  • DC to 25kHz
  • 32V max
  • 50W peak
  • open-drain MOSFET
  • optically isolated
  • RoHS, lead-free
  • DIN mountable

 

SGC-401 Isolated High-Side Driver

SGC-401 Isolated High-Side Driver

The Model SGC-401 module turns a low drive signal into a 50W peak high-side drive control signal for PLC and PC solenoid and actuator drive applications.

Model Application Input Output Features
SGC-401

SGC-401 Data Sheet
Data Sheet
(PDF - 100KB)
  • solenoid driver
  • solid-state switch
  • high-current driver
  • PLC, PC interface
  • 0 to 3.3V or 0 to 24V
  • DC to 25kHz
  • 16V max
  • 50W peak
  • MOSFET drive 
  • optically isolated
  • RoHS, lead-free
  • DIN mountable

 

SGC-100 Frequency and Duty Cycle to Voltage Converter

SGC-100 Frequency and Duty Cycle to Voltage Converter

The SGC-100 converts a pulse/signal into two 0 to 5V outputs proportional to signal frequency and duty cycle. The SGC-100 is intended for general purpose PWM monitoring in industrial control and automotive applications.

Available Q3 2017

Model Application Input Output Features
SGC-100
  • PWM signal monitor
  • freq to voltage
  • duty to voltage
  • pulse width to voltage
  • 0 to 1V to 0 to 24V
  • 10Hz to 25kHz
  • 0 to 5V
  • mV / Hz two ranges
  • 5mV / 0.1% duty
  • triple isolated (power/signal/output)
  • RoHS, lead-free
  • DIN mountable

 

DFA-100 Dual Channel Difference Amp

DFA-100 Dual Channel Difference Amp

The DFA-100 is a general purpose two channel difference amplifier for differential to single ended signal conversion for industrial control applications.

Model Application Input Output Features
DFA-100

DFA-100 Data Sheet
Data Sheet
(PDF - 108KB)
  • difference amp
  • ground-loop elimination
  • current measurement
  • sensor interfacing
  • low-level signal amplifier
  • -5V to +5V
  • DC to 100kHz
  • -5V to + 5V
  • greater than +/- 100V common mode differential inputs
  • gain = 1 (call for other gains)

 

Custom Equipment

Signal conditioning elements may be designed to your exacting specifications at a very reasonable cost. APM, Inc. is also able to modify or re-package an existing design for use in a production application. We welcome you to attach your specifications to an e-mail using the link below, or call and discuss your application with one of our engineers.

In addition to our signal conditioning product line, we offer complete engineering design services for embedded control based solutions. Please refer to our Electronic Engineering Services web page for further information.

For more information on custom signal conditioners or electronic engineering design services, email us at: engineering@appliedprocessor.com

Site created by ThomasNet Web Solutions
Applied Processor and Measurement, Inc. | High Quality, Value Minded Products... Providing Innovative Solutions